servo gear reducer

Wide range of servo gearboxes, made to fit almost all servo motors found on the market
Designed for the highest torsional stiffness and the lowest angular backlash, to get the maximum torque and overhung loads
Bush with slots and hub clamp for servomotor coupling
Enhanced dimensional compactness due to direct servomotor coupling
Widest range of feasible servomotors coupling dimensions.
The correct technical solution because of a comprehensive range of sizes, gear stages, transmission ratios, designs and non-standard designs.
Servo gear reducers (worm, coaxial, helical and bevel helical models) Catalog SR
Operating instructions:
Operating instructions for equipment reducers and gearmotors (UTD.045)
EP Drive Systems, Inc. is pleased to announce the growth of our selection of Servo Reducers, today offering five levels of precision to meet up any software requirements. The five levels of precision obtainable allows a machine developer to select the required reducer precision to meet their needs and their spending budget. They are available in both in-series and right-angle versions, in torques up to 7,376 lb.ft. and ratios to 3,392:1.
Standard applications for these reducers include rotary & linear axis drives, and material handling axis drives. Industries served include Material Handling, Automation, Aerospace, Machine Tool and Robotics.
The mounting faces of the HT, HP, Electronic and B versions are identical, making it possible to interchange a unit with a higher or lower accuracy unit if needed.
A wide range of motor couplings and installation flanges are for sale to the complete reducer range to attach virtually any servo electric motor and the hollow bore output can be used to install output shafts, pinion shafts, or other drive elements.
These reducers are typically selected predicated on the peak cycle forces, which often happen during accelerations and decelerations. These routine forces depend on the driven load, the velocity vs. period profile for the cycle, and any other external forces functioning on the axis. For more selection information, please follow this PDF link.
For application & selection assistance, please call, fax or email us. The application info will be examined by our engineers, who’ll recommend the very best solution for the application.
EP Inc. offers a full range of modular servo gearboxes /worm reducers. The modular design allows for configurations with motor input flange and output pinion for rack and pinion drives, along with solid result shafts, Hollow bore result, and insight shafts for all other positioning applications. The modular design allows for universal mounting of the gearbox in virtually any orientation.
They can be utilized on motors with a NEMA23 standard flange via an adaptor package. As the gears are normally angled, they lead to a short total amount of the motor and its gear.
The series can also be delivered both right- and left-angled and with output shafts on both sides. A 30-mm machine recess for centering and a 4 M5 threaded mounting hole may also be constructed on the gear’s output side.
Built with a simple and robust style, the series has gearing ratios that range from 6:1 to 75:1. An individual can also customize the components through the order, so as to match the apparatus to its intended application.
The Precision Planetary Gears of the EPRG series contains a thorough selection of low backlash planetary gearboxes, with up to class 3′ precision, obtainable in several gear frame sizes, with single or multiple stage reduction (for gear ratios from 1:3 to at least one 1:1,000). These models likewise incorporate versions with double shaft, right position shaft and right angle output, as well as a full range of adapters for motor mounting, making them with the capacity of meeting certain requirements of even the most diverse applications. They are designed for make use of with built-in servo and stepper EP motors, mounted directly or via adaptor flanges, but can also be used in combination with other EP motor types. This range of products is based on years of experience and represents the outcome of a decade-long research aimed at improving performance.
Optimum precision and dynamics, combined with excellent torque density, will be the key requirements specific for reliable servo gearboxes in practice. EP provides servo gearboxes for just about any app and any performance range. Our low-backlash planetary and right-angle gearboxes reflect our interest for development and the best levels of precision.
Worm equipment reducers provide market advance solution with performance and flexibility. Low amount of basic models can be applied to a wide selection of power ratings guaranteeing best performance and reduction ratios from 5 to 1000.
Gear reducers and servo gearboxes of EP Precision Machinery Co., Ltd. are designed for high-performance mechanical devices. When the motor speed must be reduced, the result torque increases and send torque completely to the application. We believe that customers will appreciate our gear reducer to achieve their demand. Just check out EP, you can obtain more information about servo gearheads, servo gearboxes, and equipment reducers. We always keep in the years ahead for your support.
Plug the Velocity Reducer in to the desired channel of your receiver, and plug the lead from your servo (or servo wye) into the male servo lead from the circuit plank. The set screw on the blue trim pot, located near the top of the main circuit board, is utilized to control the quickness of the servo. Convert the set screw fully clockwise (CW) for normal servo speed with no speed reduction, fully counter-clockwise (CCW) for optimum speed reduction, or any place in between for partial acceleration reduction. The red LED indicates three possible conditions: Slow Blinking = No Signal; Solid On = No Speed Decrease; Fast Blinking = Reduced Quickness Setting
Please note that if you make any modify to the speed establishing as the receiver is on, you must cycle power to the receiver (turn if off and back again on) for the new speed establishing to take impact. This circuit may also be used in conjunction with this Servo Reverser to cause flap or retract servos to turn in opposing directions for correct function. Instructions are included for easy installation and use.
IMPORTANT NOTE: This device will only focus on a normal, proportional servo. It will NOT focus on a retract-type servo, because they do not identify any servo positions apart from clockwise (CW) and counter-clockwise (CCW). Retract servos cannot be slowed down, also by a transmitter that includes this function, as their design and electronics do not allow it. Check the FAQ page to learn more.
This device will reduce the speed of any regular, proportional servo. Connect it in the middle of your receiver and the servo (or servos) you intend to control for a more scale-like motion of flaps or retracts. Adjustable, it could be set to lessen the quickness of your servo from super-slow motion to no speed reduction at all, with an nearly infinite quantity of positions among. Maximum reduction time for a servo to visit 90 degrees is about 14 seconds, minimum period (no reduction) is simply the normal acceleration of the servo. Ideal for reducing or eliminating the inclination of a plane to “balloon up” when flaps are deployed. It can be used to control more than one servo by utilization of a regular servo Y.
This is the new regulated version that can be used on radio systems powered by any size or type of battery, including 4.8-6.0 volt 4-5 cell Ni-Cad/Ni-MH batteries, and HV (high voltage) receivers that are powered by 2-cell 6.6-8.4 volt Li-Po/Li-Ion/LiFE batteries. This unit won’t reduce the voltage going to your servos.
The EP Gear Reducer is the perfect solution for servomotor applications such as packaging machines, gantries, injection molding devices, pick and place, and linear slides.Offered in concentric shaft, correct position solid shaft, and correct angle hollow shaft designs with modular adaptor flanges and keyless compressible bushings to quickly mount to any manufacturer’s servo motor. The EP Series helical gears possess slanted teeth in comparison to spur gears with straight cut teeth, generating a smoother gear mesh, yielding considerably lower noise levels.
The low backlash EP planetary servo gear units are made for the 30 to 350 Nm (265 to 3100 lb-in) torque classes. They were designed to combine the greatest possible flexibility and cost-efficiency because not every application requires high-performance components.
They provide a basis for diverse, dynamic and cost-optimized drive solutions.
The EP planetary servo equipment units are available in the following versions:
PSC = B5 output, clean output shaft
PSKC = B5 output, with keyway
PSCZ = B14, result, smooth output shaft
PSKCZ = B14 result, with keyway

Call us to be well-informed about servo gear reducer.


Recent Posts

gearboxes agricultural

As one of leading gearboxes agricultural manufacturers, suppliers and exporters of mechanical products, We offer gearboxes agricultural and many other products.

Please contact us for details.


Manufacturer supplier exporter of gearboxes agricultural.